initcode.html
Sizes & Specs - Commercial T/A® All Season
1An optimized footprint better distributes stress to increase tread life and lower operating costs.
2Reinforced two-ply polyester carcass absorbs shocks while stiffer tread improves steering response and road feel.
3CoolWedge™ shoulder insert enhances cooling to prolong tire life. 50,000-Mile Manufacturer's Limited Treadlife Warranty*
4Two steel belts
5Profile and sculpture with contemporary tread design
6All-season tread design (derived from our heavy truck tire)
7Dual-compound tread
8*See warranty for details.
Commercial T/A® All Season
A 50,000-mile all-season truck and fleet tire designed to help keep operating costs down.
Sizes & Specs - Commercial T/A® All Season
| Tire Size |  ServiceDescription |
Sidewall |
MSPN | Rim Width Range (inches) |
Section Width on Measuring Rim Width |
Overall Diameter |
Tread Depth (in/32nds) |
Revs/Mile at 45 mph |
Max Load (lbs@psi) |
Max Load Dual (lbs@psi) |
|---|---|---|---|---|---|---|---|---|---|---|
| LT215/85R16/E | 115/112Q | BSW | 42205 | 5.5 - 7 | 8.6 on 6 | 29.9 | 14 | 696 | 2680@80 | 2470@80 |
| LT225/75R16/E | 115/112Q | BSW | 67515 | 6 - 7 | 8.8 on 6 | 29.4 | 14 | 707 | 2680@80 | 2470@80 |
| LT235/85R16/E | 120/116Q | BSW | 45879 | 6 - 7 | 9.3 on 6.5 | 31.4 | 15 | 662 | 3042@80 | 2778@80 |
| LT245/75R16/E | 120/116Q | BSW | 89589 | 6.5 - 8 | 10 on 7 | 30.6 | 15 | 680 | 3042@80 | 2778@80 |
| LT265/75R16/E | 123/120Q | BSW | 52075 | 7 - 8 | 10.5 on 7.5 | 31.4 | 15 | 662 | 3415@80 | 3085@80 |
| LT235/80R17/E | 120/117Q | BSW | 98529 | 6 - 7.5 | 9.25 on 6.5 | 31.81 | 15 | 654 | 3085@80 | 2835@80 |
| LT245/70R17/E | 119/116Q | BSW | 36093 | 6.5 - 8 | 9.76 on 7 | 30.55 | 14 | 681 | 3000@80 | 2755@80 |
| LT245/75R17/E | 121/118Q | BSW | 49713 | 6.5 - 7.5 | 9.76 on 7 | 31.5 | 15 | 660 | 3195@80 | 2910@80 |
| LT265/70R17/E | 121/118Q | BSW | 82383 | 7 - 8.5 | 10.71 on 8 | 31.65 | 14 | 657 | 3195@80 | 2910@80 |
| LT275/70R18/E | 125/122Q | BSW | 22656 | 7 - 8.5 | 10.98 on 8 | 33.19 | 14 | 627 | 3640@80 | 3305@80 |
Government UTQG Ratings do not apply to light truck sized tires.
1. The sizes shown are average design values for tires measured on specified measuring rim widths. Some tires may vary from this value by +/-3% of the section height (affecting overall diameter), and +/-4% of the section width.
2. Section width varies approximately 0.2" (5mm) for every 0.5" change in rim width.
WARNING: Serious or fatal injury may result from tire failure due to underinflation or overloading. To ensure correct air pressure and vehicle load, refer to vehicle owner's manual or tire information placard on the vehicle. Serious injury or death may result from explosion of tire/rim assembly due to improper mounting. Only tire professionals should mount tires and they should never inflate beyond 40 psi to seat the beads. Before mixing types of tires in any configuration on any vehicle, be sure to check the vehicle owner's manual for its recommendations.
DANGER: Never mount a 16" diameter tire on a 16.5" rim.
DANGER: Never mount a 17" diameter tire on a 17.5" rim
Inflation pressure increase must not exceed the maximum pressure branded on the tire sidewall. When a customer requests a replacement tire with a lower speed rating than the original equipment tire, you must clearly communicate to him or her that the handling of the vehicle may be different, and that its maximum speed capability is limited to that of the lowest speed-rated tire on the vehicle. Exceeding the lawful speed limit is neither recommended nor endorsed.
For high-speed driving, additional inflation pressure and possibly reduced tire loading and/or upsizing is required. In the absence of specific recommendations by the vehicle manufacturer, use the following guidelines based on those in the European Tyre and Rim Technical Organization Standards Manual.
For speeds over 160km/h (100 mph), load and inflation must be adjusted according to the table below.
1. The sizes shown are average design values for tires measured on specified measuring rim widths. Some tires may vary from this value by +/-3% of the section height (affecting overall diameter), and +/-4% of the section width.
2. Section width varies approximately 0.2" (5mm) for every 0.5" change in rim width.
WARNING: Serious or fatal injury may result from tire failure due to underinflation or overloading. To ensure correct air pressure and vehicle load, refer to vehicle owner's manual or tire information placard on the vehicle. Serious injury or death may result from explosion of tire/rim assembly due to improper mounting. Only tire professionals should mount tires and they should never inflate beyond 40 psi to seat the beads. Before mixing types of tires in any configuration on any vehicle, be sure to check the vehicle owner's manual for its recommendations.
DANGER: Never mount a 16" diameter tire on a 16.5" rim.
DANGER: Never mount a 17" diameter tire on a 17.5" rim
Inflation pressure increase must not exceed the maximum pressure branded on the tire sidewall. When a customer requests a replacement tire with a lower speed rating than the original equipment tire, you must clearly communicate to him or her that the handling of the vehicle may be different, and that its maximum speed capability is limited to that of the lowest speed-rated tire on the vehicle. Exceeding the lawful speed limit is neither recommended nor endorsed.
For high-speed driving, additional inflation pressure and possibly reduced tire loading and/or upsizing is required. In the absence of specific recommendations by the vehicle manufacturer, use the following guidelines based on those in the European Tyre and Rim Technical Organization Standards Manual.
For speeds over 160km/h (100 mph), load and inflation must be adjusted according to the table below.
